Basically, a pile is a load bearing building element which is primarily used to transmit structural loads through the ground. Most of the times they are used in providing support to buildings constructed in poor soils. They can be made of different materials including concrete, steel and timber. They are usually driven in the soil until they hit the bedrock. Here are some Facts about Marine Pile Drivers
A bedrock is described as a hard soil layer situated deep in the ground. At bedrock, the piles cannot be driven any more therefore providing stability to structures above. There are two major varieties and include, friction piles and end bearing piles. When the load is transmitted to the soil via skin friction between the soil and surface of the pile, friction piles becomes necessary.
End bearing piles are used when the load is transmitted into the soil through the lower tip. Many piles depend on the combination of friction and end bearing for their supporting strengths. They may be classified of the basis of either their use or from the materials from which they are made. Selecting proper piles to use is very important and the selection should be done carefully.
Engineers are responsible for selecting the kind of piles to be used. They need to select the kind of piles that best fit a particular task and also consider all the conditions influencing both installation process and functionability. Selection piles are influenced by several conditions such as the weight and size of the structure that need to be supported.
It could be a residential or commercial building structure or just a simple structure such as water tanks. The physical properties of the soil also matter. The availability of the material for the piles and the number of piles required in order to support the structure. It is also important to establish how deep the piles need to go in order to support the structure.
The depth to which they need to be driven is very crucial in determination of the type of pile driver to be applied. Piles are usually driven underground using load drivers. Before piles are driven, the type of driver to be used must be determined is advance. Factors like basic penetration test, geotechnical study and site study are crucial in determining the driving device. Load test in which the total load to be carried by the piles is determined is another very important test.
While driving the piles into the ground, the force that supports the pile down the ground is equal to the resistance force to piles. To solve this, pile drivers becomes important. They help create the force needed to move the piles down the ground.
The commonest tools used are driving hammers for piles. They include diesel hammers. The hammers are used in imparting compression and explosion energy required in the process. The other type of hammer is the vibratory hammer. This one uses shafts spinning in opposing direction to drive the piles through the soil.
A bedrock is described as a hard soil layer situated deep in the ground. At bedrock, the piles cannot be driven any more therefore providing stability to structures above. There are two major varieties and include, friction piles and end bearing piles. When the load is transmitted to the soil via skin friction between the soil and surface of the pile, friction piles becomes necessary.
End bearing piles are used when the load is transmitted into the soil through the lower tip. Many piles depend on the combination of friction and end bearing for their supporting strengths. They may be classified of the basis of either their use or from the materials from which they are made. Selecting proper piles to use is very important and the selection should be done carefully.
Engineers are responsible for selecting the kind of piles to be used. They need to select the kind of piles that best fit a particular task and also consider all the conditions influencing both installation process and functionability. Selection piles are influenced by several conditions such as the weight and size of the structure that need to be supported.
It could be a residential or commercial building structure or just a simple structure such as water tanks. The physical properties of the soil also matter. The availability of the material for the piles and the number of piles required in order to support the structure. It is also important to establish how deep the piles need to go in order to support the structure.
The depth to which they need to be driven is very crucial in determination of the type of pile driver to be applied. Piles are usually driven underground using load drivers. Before piles are driven, the type of driver to be used must be determined is advance. Factors like basic penetration test, geotechnical study and site study are crucial in determining the driving device. Load test in which the total load to be carried by the piles is determined is another very important test.
While driving the piles into the ground, the force that supports the pile down the ground is equal to the resistance force to piles. To solve this, pile drivers becomes important. They help create the force needed to move the piles down the ground.
The commonest tools used are driving hammers for piles. They include diesel hammers. The hammers are used in imparting compression and explosion energy required in the process. The other type of hammer is the vibratory hammer. This one uses shafts spinning in opposing direction to drive the piles through the soil.
About the Author:
Get fantastic pile driver purchase tips, today. You can also get more information about state-of-the-art marine pile drivers at http://www.piledriver.org right now.
No comments:
Post a Comment